Development of Au Nanoparticle Two-Dimensional Assemblies Dispersed with Au Nanoparticle-Nanostar Complexes and Surface-Enhanced Raman Scattering Activity.

We recently found that polyvinylpyrrolidone (PVP)-protected metal nanoparticles dispersed in water/butanol mixture spontaneously float to the air/water interface and form two-dimensional assemblies due to classical surface excess theory and Rayleigh-Bénard-Marangoni convection induced by butanol evaporation. In this study, we found that by leveraging this principle, a unique structure is formed where hetero gold nanospheres (AuNPs)/gold nanostars (AuNSs) complexes are dispersed within AuNP two-dimensional assemblies, obtained from a mixture of polyvinylpyrrolidone-protected AuNPs and AuNSs that interact electrostatically with the AuNPs. These structures were believed to form as a result of AuNPs/AuNSs complexes formed in the water/butanol mixture floating to the air/water interface and being incorporated into the growth of AuNP two-dimensional assemblies. These structures were obtained by optimizing the amount of mixed AuNSs, with excessive addition resulting in the formation of random three-dimensional network structures. The AuNP assemblies dispersed with AuNPs/AuNSs complexes exhibited significantly higher Raman (surface-enhanced resonance Raman scattering: SERRS) activity compared to simple AuNP assemblies, while the three-dimensional network structure did not show significant SERRS activity enhancement. These results demonstrate the excellent SERRS activity of AuNP two-dimensional assemblies dispersed with hetero AuNPs/AuNSs complexes.

A plasmonic metasurface reveals differential motility of breast cancer cell lines at initial phase of adhesion.

A plasmonic metasurface composed of a self-assembled monolayer of gold nanoparticles allows for fluorescence imaging with high spatial resolution, owing to the collective excitation of localized surface plasmon resonance. Taking advantage of fluorescence imaging confined to the nano-interface, we examined actin organization in breast cancer cell lines with different metastatic potentials during cell adhesion. Live-cell fluorescence imaging confined within tens of nanometers from the substrate shows a high actin density spanning < 1 µm from the cell edge. Live-cell imaging revealed that the breast cancer cell lines exhibited different actin patterns during the initial phase of cell adhesion (∼ 1 h). Non-tumorous MCF10A cells exhibited symmetric actin localization at the cell edge, whereas highly metastatic MDA-MB-231 cells showed asymmetric actin localization, demonstrating rapid polarization of MDA-MB-231 cells upon adhesion. The rapid actin organization observed by our plasmonic metasurface-based fluorescence imaging provides information on how quickly cancer cells sense the underlying substrate.

Two-dimensional assembled PVP-modified silver nanoprisms guided by butanol for surface-enhanced Raman scattering-based invisible printing platforms.

This study proposes a methodology for the fabrication of two-dimensional assembled colloidal nanocrystals based on the classical theory for the surface excess of a short-chain alcohol (butanol) in an aqueous mixture and Rayleigh-Bénard-Marangoni convection caused by temperature and/or surface tension gradients due to the volatilization of butanol at the air-water interface. When polyvinylpyrrolidone (PVP)-modified anisotropic silver nanoprisms dispersed in butanol were added into the water phase, the nanoprisms were guided to the air-water interface via adsorbed butanol together with free butanol and formed dense two-dimensional assemblies through the lateral attraction between nanoprisms as the adsorbed butanol was volatilized. The obtained dense film composed of silver nanoprisms exhibited surface-enhanced Raman scattering (SERS) activity, and in particular, the activity was largely enhanced by low-pressure plasma treatment. A SERS-based invisible printing platform that could only be recognized by x-y SERS mapping was demonstrated with the patterned nanoprism films.

Tuning the Emission Wavelength of Lead Halide Perovskite NCs via Size and Shape Control.

The advent of lead halide perovskite nanocrystals (NCs), which are easily synthesized, ultralow-cost materials and have an impeccable luminous efficiency, has drastically changed the future perspective of semiconductor quantum dot devices. Although the band gap energy of lead perovskite NCs can be tuned by the halide composition, the instability problem prevails for mixed-halide perovskite NCs, caused by phase segregation due to ion migration when an external electric field or light is applied. To avoid this problem and obtain the stable emission of RGB primary colors, in this study, two synthesis pathways of pure-halide perovskite NCs are proposed. One approach is the modified hot injection method with "centrifugation of a frozen eutectic mixture" to separate small NCs efficiently, and the other is the "low-temperature mixing and heat-up method" for target materials including CsPbI3, CsPbBr3, and CH(NH2)2PbBr3 (FAPbBr3). The emission wavelength of FAPbBr3 is tuned ion-stoichiometrically, unlike Cs perovskites. These various synthesis pathways of pure-halide perovskite NCs enable the efficient production of high-quality perovskite NCs and allow precise tuning of the emission color to the desired wavelength. Although there are still several "gaps" remaining in the available emission wavelength, the new methodology proposed in this study could potentially be employed for manufacturing more stable perovskite NC-based optoelectronic devices.

All-inorganic perovskite quantum dot light-emitting memories.

Field-induced ionic motions in all-inorganic CsPbBr3 perovskite quantum dots (QDs) strongly dictate not only their electro-optical characteristics but also the ultimate optoelectronic device performance. Here, we show that the functionality of a single Ag/CsPbBr3/ITO device can be actively switched on a sub-millisecond scale from a resistive random-access memory (RRAM) to a light-emitting electrochemical cell (LEC), or vice versa, by simply modulating its bias polarity. We then realize for the first time a fast, all-perovskite light-emitting memory (LEM) operating at 5 kHz by pairing such two identical devices in series, in which one functions as an RRAM to electrically read the encoded data while the other simultaneously as an LEC for a parallel, non-contact optical reading. We further show that the digital status of the LEM can be perceived in real time from its emission color. Our work opens up a completely new horizon for more advanced all-inorganic perovskite optoelectronic technologies.

Rapid Discrimination of Extracellular Vesicles by Shape Distribution Analysis.

A rapid and simple cancer detection method independent of cancer type is an important technology for cancer diagnosis. Although the expression profiles of biological molecules contained in cancer cell-derived extracellular vesicles (EVs) are considered candidates for discrimination indexes to identify any cancerous cells in the body, it takes a certain amount of time to examine these expression profiles. Here, we report the shape distributions of EVs suspended in a solution and the potential of these distributions as a discrimination index to discriminate cancer cells. Distribution analysis is achieved by low-aspect-ratio nanopore devices that enable us to rapidly analyze EV shapes individually in solution, and the present results reveal a dependence of EV shape distribution on the type of cells (cultured liver, breast, and colorectal cancer cells and cultured normal breast cells) secreting EVs. The findings in this study provide realizability and experimental basis for a simple method to discriminate several types of cancerous cells based on rapid analyses of EV shape distributions.

Thermodynamic Control in the Synthesis of Quantum-Confined Blue-Emitting CsPbBr3 Perovskite Nanostrips.

Size control is critical in the synthesis of quantum-confined semiconductor nanocrystals, otherwise known as quantum dots. The achievement of size-uniformity and narrow spectral line-width in quantum dots conventionally relies on a very precise kinetic control of the reactions, where reaction time plays a significant role in defining the final crystal sizes and distribution. Here, we show that synthesis of quantum-confined perovskite nanostrips could be achieved through a thermodynamically controlled reaction, using a low-temperature and ligand-rich approach. The nanostrip growth proceeds through an initial one-dimensional (1D) nanorod stage, followed by the lateral widening of the rod to form a two-dimensional (2D) nanostrip. The spectral characteristics of the final product remain unchanged after prolonged reaction, indicating no signs of crystal ripening and confirming the thermodynamic nature of this reaction. The CsPbBr3 perovskite nanostrips were highly uniform and emit at a deep-blue wavelength of 462 nm with a remarkably narrow line-width of 13 nm. This corresponds to color coordinates of (0.136, 0.049) on the CIE 1931 color space, which fulfils the stringent Rec. 2020 standard for next-generation color displays. The well-passivated nanostrips also possess negligible defects and provide a near-unity photoluminescence quantum yield at 94%. Crucially, the achievement of blue emission through a pure-halide perovskite circumvents the problems of spectral instability that are frequently experienced in mixed-halide perovskite systems. The convenience and scalability of our thermodynamic approach, coupled with the excellent optical attributes, would likely enable these quantum-confined perovskite systems to be the preferred method toward color control in trichromatic display applications.

Nonlinear Viscoelasticity of Highly Ordered, Two-Dimensional Assemblies of Metal Nanoparticles Confined at the Air/Water Interface.

In this study, we investigated the viscoelastic properties of metal nanoparticle monolayers at the air/water interface by dilational rheology under periodic oscillation of surface area. Au nanoparticles capped with oleylamine form a stable, dense monolayer on a Langmuir film balance. The stress response function of a nanoparticle monolayer was first analyzed using the classical Kelvin-Voigt model, yielding the spring constant and viscosity. The obtained results suggest that the monolayer of nanoparticles is predominantly elastic, forming a two-dimensional physical gel. As the global shape of the signal exhibited a clear nonlinearity, we further analyzed the data with the higher modes in the Fourier series expansion. The imaginary part of the higher mode signal was stronger than the real part, suggesting that the dissipative term mainly causes the nonlinearity. Intriguingly, the response function measured at larger strain amplitude became asymmetric, accompanied by the emergence of even modes. The significance of interactions between nanoparticles was quantitatively assessed by calculating the potential of mean force, indicating that the lateral correlation could reach up to the distance much larger than the particle diameter. The influence of surface chemical functions and core metal has also been examined by using Au nanoparticles capped with partially fluorinated alkanethiolate and Ag nanoparticles capped with myristic acid. The combination of dilational rheology and correlation analyses can help us precisely control two-dimensional colloidal assembly of metal nanoparticles with fine-adjustable localized surface plasmon resonance.

The Role of Citric Acid in the Stabilization of Nanoparticles and Colloidal Particles in the Environment: Measurement of Surface Forces between Hafnium Oxide Surfaces in the Presence of Citric Acid.

The interactions between colloidal particles and nanoparticles determine solution stability and the structures formed when the particles are unstable to flocculation. Therefore, knowledge of the interparticle interactions is important for understanding the transport, dissolution, and fate of particles in the environment. The interactions between particles are governed by the surface properties of the particles, which are altered when species adsorb to the surface. The important interactions in the environment are almost never those between the bare particles but rather those between particles that have been modified by the adsorption of natural organic materials. Citric acid is important in this regard not only because it is present in soil but also as a model of humic and fulvic acids. Here we have studied the surface forces between the model metal oxide surface hafnia in the presence of citric acid in order to understand the stability of colloidal particles and nanoparticles. We find that citric acid stabilizes the particles over a wide range of pH at low to moderate ionic strength. At high ionic strength, colloidal particles will flocculate due to a secondary minimum, resulting in aggregates that are dense and easily redispersed. In contrast, nanoparticles stabilized by citric acid remain stable at high ionic strengths and therefore exist in solution as individual particles; this will contribute to their dispersion in the environment and the uptake of nanoparticles by mammalian cells.

LSPR-mediated high axial-resolution fluorescence imaging on a silver nanoparticle sheet.

This paper reports our original technique for visualizing cell-attached nanointerfaces with extremely high axial resolution using homogeneously excited localized surface plasmon resonance (LSPR) on self-assembled silver nanoparticle sheets. The LSPR sheet can confine and enhance the fluorescence at the nanointerface, which provides high signal-to-noise ratio images of focal adhesion at the cell-attached interface. The advantage of this LSPR-assisted technique is its usability, which provides comparable or higher-quality nanointerfacial images than TIRF microscopy, even under epifluorescence microscopy. We also report the cytotoxicity of silver nanoparticles, as determined via morphological analysis of adherent cells on the sheet.

Large patternable metal nanoparticle sheets by photo/e-beam lithography.

Techniques for micro/nano-scale patterning of large metal nanoparticle sheets can potentially be used to realize high-performance photoelectronic devices because the sheets provide greatly enhanced electrical fields around the nanoparticles due to localized surface plasmon resonances. However, no single metal nanoparticle sheet currently exists with sufficient durability for conventional lithographical processes. Here, we report large photo and/or e-beam lithographic patternable metal nanoparticle sheets with improved durability by incorporating molecular cross-linked structures between nanoparticles. The cross-linked structures were easily formed by a one-step chemical reaction; immersing a single nanoparticle sheet consisting of core metals, to which capping molecules ionically bond, in a dithiol ethanol solution. The ligand exchange reaction processes were discussed in detail, and we demonstrated 20 µm wide line and space patterns, and a 170 nm wide line of the silver nanoparticle sheets.

High-resolution imaging of a cell-attached nanointerface using a gold-nanoparticle two-dimensional sheet.

This paper proposes a simple, effective, non-scanning method for the visualization of a cell-attached nanointerface. The method uses localized surface plasmon resonance (LSPR) excited homogeneously on a two-dimensional (2D) self-assembled gold-nanoparticle sheet. The LSPR of the gold-nanoparticle sheet provides high-contrast interfacial images due to the confined light within a region a few tens of nanometers from the particles and the enhancement of fluorescence. Test experiments on rat basophilic leukemia (RBL-2H3) cells with fluorescence-labeled actin filaments revealed high axial and lateral resolution even under a regular epifluorescence microscope, which produced higher quality images than those captured under a total internal reflection fluorescence (TIRF) microscope. This non-scanning-type, high-resolution imaging method will be an effective tool for monitoring interfacial phenomena that exhibit relatively rapid reaction kinetics in various cellular and molecular dynamics.

Electromagnetically induced transparency of a plasmonic metamaterial light absorber based on multilayered metallic nanoparticle sheets.

In this study, we observed the peak splitting of absorption spectra for two-dimensional sheets of silver nanoparticles due to the electromagnetically induced transparency (EIT) effect. This unique optical phenomenon was observed for the multilayered nanosheets up to 20 layers on a metal substrate, while this phenomenon was not observed on a transparent substrate. The wavelength and intensities of the split peaks depend on the number of layers, and the experimental results were well reproduced by the calculation of the Transfer-Matrix method by employing the effective medium approximation. The Ag nanosheets used in this study can act as a plasmonic metamaterial light absorber, which has a such large oscillator strength. This phenomenon is a fundamental optical property of a thin film on a metal substrate but has never been observed because native materials do not have a large oscillator strength. This new type of EIT effect using a plasmonic metamaterial light absorber presents the potential for the development of future optic and photonic technologies.

Colorimetric Detection of an Airborne Remote Photocatalytic Reaction Using a Stratified Ag Nanoparticle Sheet.

Photocatalysts are practically used for decomposition of harmful and fouling organic compounds. Among the photocatalytic reactions, remote oxidation via airborne species is a relatively slow process, so that a sensitive technique for its detection has been awaiting. Here, we investigated an airborne remote photocatalytic reaction of a TiO2 photocatalyst modified with Pt nanoparticles as co-catalysts via the color change caused by a decomposition of a multilayered silver nanoparticle sheet. The silver nanoparticle sheet fabricated by the Langmuir-Schaefer method on a gold substrate exhibits a unique multicolor depending upon the number of layers. The color originates from multiple light trapping in the stratified sheets that has a metamaterial characteristic along with an intra- and interlayer coupling of localized surface plasmon resonance (LSPR). The stepwise decomposition of the sheets was confirmed by the colorimetric data, which exhibited not only a monotonic decrease but also a maximized absorption of light when the film thickness reached the optimal thickness for light trapping or when the oxidation of the Ag core started. Scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and surface plasmon resonance (SPR) spectroscopy data provided a complete view of the decomposition process of this inorganic-organic nanocomposite film, and simulation by the transfer-matrix method explained a simultaneous plasmonic response rationally. The influence of the humidity and gas flow rate on the airborne remote photocatalytic reaction kinetics was examined by this colorimetric detection method, and it suggests that H2O in air plays an essential role in the reaction.

Feature issue introduction: biophotonic materials and applications.

Biophotonics can be defined as the interplay of light and biological matter. The percolation of new optical technology into the realm of biology has literally shed new light into the inner workings of biological systems. This has revealed new applications for optics in biology. In a parallel trend, biomolecules have been investigated for their optical applications. Materials are playing a central role in the development of biophotonics. New materials, fabrication methods, and structures are enabling new biosensors, contrast agents, imaging strategies, and assay methods. Similarly, biologic materials themselves can be used in photonic devices. In this context, two open-access, rapid-publication journals from The Optical Society of America (OSA), Optical Materials Express and Biomedical Optics Express, will publish a joint feature issue covering advances in biophotonics materials.

Characteristics of localized surface plasmons excited on mixed monolayers composed of self-assembled Ag and Au nanoparticles.

The fundamental characteristics of localized surface plasmon resonance (LSPR) excited on mixed monolayers composed of self-assembled Ag and Au nanoparticles (AgNPs and AuNPs, respectively) were investigated. Mixed monolayered films were fabricated at the air-water interface at different mixing ratios. The films retained their phase-segregated morphologies in which AuNPs formed several 10 to 100 nm island domains in a homogeneous AgNP matrix phase. The LSPR bands originating from the self-assembled domains shifted to longer wavelengths as the domain size increased, as predicted by a finite-difference time-domain (FDTD) simulation. The FDTD simulation also revealed that even an alternating-lattice-structured two-dimensional (2D) AgNP/AuNP film retained two isolated LSPR bands, revealing that the plasmon resonances excited on each particle did not couple even in a continuous 2D sheet, unlike in the homologous NP system. The fluorescence quenching test of Cy3 and Cy5 dyes confirmed that the independent functions of AuNPs and AgNPs remained in the mixed films, whereas the AuNPs exhibited significantly higher quenching efficiency for the Cy3 dye compared with AgNPs due to the overlap of the excitation/emission bands of the dyes with the AuNP LSPR band. Various applications can be considered using this nanoheterostructured plasmonic assembly to excite spatially designed, high-density LSPR on macroscopic surfaces.

Colorimetric plasmon sensors with multilayered metallic nanoparticle sheets.

Colorimetric plasmon sensors for naked-eye detection of molecular recognition events have been proposed. Here, 3-layered Ag nanoparticle (NP) sheets on a Au substrate fabricated using the Langmuir-Schaefer method were utilized as the detection substrates. A drastic color change was observed following the binding of Au NPs via avidin-biotin interactions at less than 30% surface coverage. The color change was attributed not only to the localized surface plasmon resonance (LSPR) of the adsorbed Au NPs but also to the multiple light trapping effect derived from the stratified Au and Ag NPs, as predicted by a finite-difference time-domain (FDTD) simulation. This plasmonic multi-color has great potential in the development of simple and highly sensitive diagnostic systems.

Characterization of citrates on gold and silver nanoparticles.

In this paper, we report different coordinations of citrates on gold (AuNP) and silver (AgNP) nanoparticles, as determined using Fourier transform infrared spectroscopy (FTIR) and molecular orbital (MO) calculations. AuNPs and AgNPs are found to have completely different interactions with the carboxylate anchoring groups, as indicated by their unique asymmetric stretching vibrations in the FTIR spectra. The ν(as) (COO(-)) of citrate exhibits a high-frequency shift resulting from the formation of a unidentate coordination on AuNPs, whereas this vibration exhibits a low-frequency shift as a result of ionic bond formation on AgNPs, as predicted from the MO calculations of the corresponding metal complex salts. The enhancement in the IR signals when their vibration direction was perpendicular to the nanoparticle surface revealed the influence of localized surface plasmons excited on the metal nanoparticles.

Surface plasmon resonance properties of silver nanoparticle 2D sheets on metal gratings.

Grating-coupled propagating surface plasmons associated with silver-nanoparticle 2D crystalline sheets exhibit sensitive plasmonic resonance tuning. Multilayered silver-nanoparticle 2D crystalline sheets are fabricated on gold or silver grating surfaces by the Langmuir- Blodgett method. We show that the deposition of Ag crystalline nanosheets on Au or Ag grating surfaces causes a drastic change in propagating surface plasmon resonance (SPR) both in angle measurements at fixed wavelengths and in fixed incident-angle mode by irradiation of white light. The dielectric constant of the multilayered silver nanosheet is estimated by a rigorous coupled-wave analysis. We find that the dielectric constant drastically increases as the number of silver-nanosheet layers increases. The experimentally obtained SP dispersions of Ag crystalline nanosheets on Au and Ag gratings are compared with the calculated SP dispersion curves. The drastic change in the surface plasmon resonance caused by the deposition of Ag-nanoparticle 2D crystalline sheets on metal grating surfaces suggests the potential for applications in highly sensitive sensors or for plasmonic devices requiring greatly enhanced electric fields.

Grain size dependence of surface plasmon enhanced photoluminescence.

Photoluminescence (PL) in the InGaN quantum well based light-emitting diodes (LED) is greatly mediated through the coupling with the Surface Plasmons (SPs) at the interface of the sputtered Ag film. SPs coupled PL is independently tuned through controlling the grain size of the sputtered Ag films. The grain size of ~50 nm exhibits the maximum light extraction efficiency (LEE) at the wavelength of 460 nm. This grain size agrees with the periodic lattice constant of the grating structure in the calculation, where the momentum mismatch between the SPs and the radiative light can be compensated.